Material: 7075 Aluminum Coating: Matte Black Hardcoat Overall Length: 1.78" Overall Width: 1.1" Mounting Hardware: (2) 8-32 Button Head Screws, (1) 8-32 Set Screw) Red Dot Fitment: Trijicon RMR, Holosun HS507C This mount fits: Walther PPQ Classic (M1) Walther PPQ M2 (All Models) Walther PPQ 45 Walther PPQ 45 SD Walther PPQ Sub Compact Walther P99 (All Models) Walther PPX (All Models) Walther Creed Walther Creed 10 Round Walther PPS (All Models) Walther PPS M2 (All Models) This mount does not fit: Walther PPQ 22 Walther PPQ Q4 Tac Walther Q5 Match Simply remove the rear sight on your gun and replace it with our mount in order to mount your Trijicon RMR red-dot sight. No alterations are required. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Installation Instructions Remove the rear sight* Install the EGW Sight Mount in the dovetail Tighten set screw (if applicable) Place the red dot sight on the EGW Sight Mount (placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.) Apply blue Loctite to the provided mounting screws Torque mounting screws to 15in/lbs The screws that are included with this mount require a 5/64'' allen wrench for installation.
Material: 7075 Aluminium Beschichtung: Matt Schwarz Hartanodisiert Gesamtlänge: 1,78" Gesamtbreite: 1,1" Montagematerial: (2) 8-32 Senkkopfschrauben, (1) 8-32 Set-Schraube) Rotpunkt-Kompatibilität: Trijicon RMR, Holosun HS507C Diese Halterung passt auf: Walther PPQ Classic (M1) Walther PPQ M2 (Alle Modelle) Walther PPQ 45 Walther PPQ 45 SD Walther PPQ Sub Compact Walther P99 (Alle Modelle) Walther PPX (Alle Modelle) Walther Creed Walther Creed 10 Schuss Walther PPS (Alle Modelle) Walther PPS M2 (Alle Modelle) Diese Halterung passt nicht auf: Walther PPQ 22 Walther PPQ Q4 Tac Walther Q5 Match Entferne einfach die Kimme deines Gewehrs und ersetze sie durch unsere Halterung, um dein Trijicon RMR Rotpunktvisier zu montieren. Es sind keine Änderungen erforderlich. Du kannst unsere Halterung jederzeit abnehmen und deine Kimme wieder einsetzen. Montagematerial ist enthalten. Installationsanleitung Entferne die Kimme* Installiere die EGW Visierhalterung in der Nut Ziehe die Set-Schraube fest (falls zutreffend) Platziere das Rotpunktvisier auf der EGW Visierhalterung (ein kleines Stück Papier zwischen dem Rotpunktvisier und der Halterung erleichtert die Entfernung und verhindert, dass Loctite auf das Rotpunktvisier gelangt.) Trage blauen Loctite auf die bereitgestellten Montageschrauben auf. Ziehe die Montageschrauben auf 15in/lbs fest. Die mit dieser Halterung gelieferten Schrauben benötigen einen 5/64'' Inbusschlüssel für die Installation.