873750000152 Der Aluminium-Abzugsbügel ersetzt den originalen Abzugsbügel und ermöglicht vollen Zugang zum Abzug, selbst wenn du Handschuhe trägst. Damit entfällt die Notwendigkeit, den Abzugsbügel bei kaltem Wetter abzunehmen, um an den Abzug zu gelangen. Der Abzugsbügel bietet eine übergroße Öffnung und wird mit standardmäßigen Rollstiften und Setzschrauben befestigt. Er eliminiert die Notwendigkeit für einen Lückenstopfen und funktioniert mit den meisten Griffen.
Auf Lager
Lieferzeit ca. 1-4 Tage. 1 Stk. im lokalen Lager Mehr als 10 Stk. im Großlager
Lieferzeit ca. 1-4 Tage. 1 Stk. im lokalen Lager Mehr als 10 Stk. im Großlager
Aluminum triggerguard replaces factory guard and gives full access to the trigger, even when you’re wearing gloves. Ends the complication of having to drop the triggerguard in cold weather environments in order to get to the trigger. Trigger guard gives you an oversized opening and is held in place with standard roll pins and set screws. Eliminates need for gap plug and works with most grips.
Hält den Abzug zugänglich, selbst mit Handschuhen
Der Aluminium-Abzugsbügel ersetzt den originalen Abzugsbügel und ermöglicht vollen Zugang zum Abzug, selbst wenn du Handschuhe trägst. Damit entfällt die Notwendigkeit, den Abzugsbügel bei kaltem Wetter abzunehmen, um an den Abzug zu gelangen. Der Abzugsbügel bietet eine übergroße Öffnung und wird mit standardmäßigen Rollstiften und Setzschrauben befestigt. Er eliminiert die Notwendigkeit für einen Lückenstopfen und funktioniert mit den meisten Griffen.
Top Takeaways
Der Aluminium-Abzugsschutz sorgt für vollen Zugang zum Abzug, auch mit Handschuhen.
Er hat eine vergrößerte Öffnung und wird mit standardmäßigen Rollstiften und Madenschrauben befestigt.
Kompatibel mit den meisten Griffen und eliminiert die Notwendigkeit für eine Spaltabdeckung.
Eigenschaften
Finish:Black
Hersteller/Modell:AR-15
Versandgewicht:0,045kg
Versandhöhe:38mm
Versandbreite:102mm
Versandlänge:171mm
UPC:873750000152
Artikeldetails
Made in USA
US-Exportklassifizierung: 0A501.x
Kundenbewertungen
Kundenbewertungen (32)
4,3 / 5
Sehr empfehlenswert
Good product. Works as advertised. 05.08.2017
I have two of these on two different mil-spec lowers. Good fit, looks nice and fills the gap on back of trigger guard. If you have a grip that also fills that gap you'll have to trim it a little. Of course it helps to have the right tools. A roll pin punch really helps and a roll pin starter punch is nice but not mandatory. You'll need a 1/16" Allen wrench but any decent set should have that size. Gives you a little more finger room if you are wearing heavy gloves.
Sehr empfehlenswert
Just what i needed! 04.09.2016
This was just the ticket to solving an issue for my AR15. Got a mil spec trigger guard that was out of spec and wouldn't allow my mags to drop free. Installed this and it was all fixed, very pleasing trigger guard.
Sehr empfehlenswert
Another Nice Magpul Product 21.12.2014
I have installed this product (enhanced, i.e. metal version) on 3 different AR lowers, Bushmaster, Spikes Tactical, and a Palmetto State Armory. Never had any issues, finish is quality work, and nicely replaces the unsightly flat plastic trigger guard. Highly recommend this product and will use this product on future builds.
Bedingt empfehlenswert
Not so happy... 18.11.2014
So, I love Magpul. And I really like this trigger guard, but oh my heck was it a pain to install! They require the worlds smallest fallen wrench. But the worst part of all is, THE POLY VERSION IS NOT TAPPED! YOU HAVE TO TAP IT! Magpul expects you to use the given screw as a tapping screw...well, that only strips the screw...so, unless you have a tapping kit, be aware. Also, I had to scrape away all the loctite with a wire brush. I finally got it installed and love it. If you do buy this, consider buying a advanced screw kit for it. I am only giving it 3 stars cause I love Magpul.
Sehr empfehlenswert
Great addition for any AR style 18.08.2014
Love this trigger guard, and require it on all my builds. Easy to install (with proper care taken to drift in roll pin) and very sturdy once in place.
Perfect fit on my lowers (Mega Arms).
Best part about it, there is no giant Magpul logo etched into the bottom like the polymer version.
Sehr empfehlenswert
Should be standard on all AR's 18.11.2013
Not overly large or goofy-looking like some others; the Magpul design looks right and is perfectly functional. Big enough to get your finger in no matter what glove you wear. Have installed a few of these and never had an issue with fitment. Magpul makes another model much less expensive, but its made of plastic... I much prefer this alloy version.
Sehr empfehlenswert
Should be a Standard Item 06.05.2013
It adds the perfect amount of extra room for gloves. It looks good and is durable. What more could you ask for?
Sehr empfehlenswert
Looks awesome 24.06.2012
gives a custom look to my AR
Sehr empfehlenswert
Great for big hands 05.02.2012
This is the easiest and one of the most beneficial changes I have made to my AR (a DPMS). A couple taps on a roll pin punch and a few turns on an allen key. Other reviews address fit issue but for a DPMS lower the fit is as good as can be, to fit any better the trigger guard would have to be part of the lower.
Sehr empfehlenswert
Perfect.. 07.08.2011
Easy install, fit my RR with no issues. Looks great.
Empfehlenswert
Nice lines, great product 19.04.2011
I don't know how much more room it provides, but it gives a little more room and looks great installed. Fairly easy to install and the aluminum doesn't add any felt weight and I'm not crazy about too much plastic. Great product.
Sehr empfehlenswert
Highly Recommend It! 09.04.2011
I have Placed this part on three AR Rifles (1 Armalite & 2 Bushmaster) with no problem. Not only is it highly functional but it looks good too!
Sehr empfehlenswert
Go Ahead... you know you want to... 22.01.2011
I'm not at all the sort of person who drinks the Kool Aid just for the looks of it... except with this one. Yes, I suppose the opening is larger for gloves, but I got this for no other reason than it fits the lines of an AR perfectly, and almost makes it a good looking gun. It's built like a rock, so durability isn't an issue. Be warned that you can forget about unhinging it for gloves in the wintertime if that's something your accustomed to with the standard trigger guard. Also, if you're building your lower from scratch, just buy this right away and install it, as knocking that old pin out sometimes isn't as easy as it should be-- best to install one guard one time. Also, MagPul has since come out with a less expensive "plastic" version that I'd consider going with now, both for price and weight savings, although it is nice to know that this thing won't ever break.
Sehr empfehlenswert
MAGPUL Enhanced M16 Trigger Guard 26.10.2010
Just installed it on my Colt 6921 M4LE and it fits great! It was easy to install. NO MODIFICATION NEEDED. It took me no more that 2mins to install. No problems!!
Bedingt empfehlenswert
Problems 02.07.2010
I love MAGPUL, but this trigger guard was such hassle to install. I had to file down the edges to get it to it my POF lower. Something that I feel I shouldn't have to do when I'm spending [$] for a little piece of metal. Next time I'll try the MOE trigger guard that is much cheaper than this.
Nicht empfehlenswert
Does not fully cover the gap on my Colt 12.06.2010
I bought this trigger guard for one reason only: to fill the gap that exists with the standard trigger guard. I did not buy it because I needed extra space in the trigger guard. I chose not to buy a simple rubber plug to fill this gap but to go for this, what I though to be, very hight quality product. Well, it is nicely made and so, but it just does not completely prevent the edges from the trigger guard base to protrude and still hurt my finger. It is better than the standard trigger guard, but if it had had a milimeter of extra thickness it would have worked well. Now it has not solved my problem on my Colt AR-15 Sporter A2 HB. I'm really disappointed.
Empfehlenswert
Exactly What I Was Looking For 12.04.2010
I bought the enhanced trigger guard in order to prevent the occasional trigger pinch to my finger that occurs with a standard trigger guard. After going to the range, I am very pleased with this upgrade.
As others have noted, the roll pin is not that easy to install. I had to work at it for a while and the whole time I was holding my breath that I didn't damage the lower receiver mounts (next time I will use an AR bench block rather than a makeshift block). Thankfully, I got it installed and have no plans to remove it.
Sehr empfehlenswert
The Best Aftermarket Trigger Guard Out 14.03.2010
Magpul has a real win on their hands with this trigger guard. The enhanced trigger guard has several things going for it. First, it is robustly built out of aluminum with a nice phosphate coating that matches most lowers. Second, its curvature offers much more space in the trigger area for bigger fingers or gloves. Third, and what I consider most important, is that it covers the gap between the standard trigger and the grip. You know that gap, the one that cuts into your index finger, causing blisters after short periods of shooting. Finally, it is very quick and easy to install.
Magpul does make a similar trigger guard made from plastic that is about half the cost, but truthfully, the solid aluminum construction is absolutely worth it. Grab this item, you will not be disappointed.
Sehr empfehlenswert
Enhanced Trigger Guard 12.03.2010
Fit like a glove, no fitting required, and adds just enough room for gloves, without dropping far enough to interfier with other mods. Finish was a little lighter than the gun finish, but they can't match every gun out there. Def. a recomended product.
Nicht empfehlenswert
Needs fitting on DPMS 01.03.2010
It is not drop in on my DPMS
Sehr empfehlenswert
Great Product 27.02.2010
This is a great product. I have one on all three of my rifles. Every easy to install...
Sehr empfehlenswert
Outstanding 18.11.2009
Perfect fit to S&W lower, filled the gap at the pistol grip, easy install. Great product
Bedingt empfehlenswert
"Drop in" isn't as drop in as it sounds 27.10.2009
This item is not drop in as it may seem. The mil-spec parts are super easy to remove, but the replacements from Magpul are not as forgiving. Best bet is to let the gunsmith take care of it. The replacement roll pin is very difficult to drift in. I needed to pound it into place. Not really sure it does more than just look really tactical.
Sehr empfehlenswert
Perfect. 25.10.2009
Hands down the best trigger guard ever.
Empfehlenswert
Triggerguard 23.09.2009
Adds just enough room for gloves and it covers up that gap between the pistol grip and the trigger guard. It was kind of a pain to install though.
Empfehlenswert
Goes along nice with MAGPUL Grip 21.09.2009
This works wonderful with the MAGPUL grip. No more buying gapper for standard trigger guard.
Nicht empfehlenswert
Poor Fittment, cheap qaulity. 12.09.2009
This Enhanced Triggergaurd did not fit my Bushmaster M4 A3 well with misalignment at the set screw end . The finish color is off and there are no manufacturing markings like the picture shows,so it looks genaric.....
Sehr empfehlenswert
Excellent upgrade 10.09.2009
Excellent fit and finish with no more sharp edges to contend with. I have them on all my ARs. Roll pin removal (of old trigger guard) and installation of the new one is the most difficult part. Quickest way to install - use a bench vice. Just oil up the pin, place the trigger guard in place and begin by tapping in the roll pin. Once it takes hold on one side - line up "ears" of the lower in the bench vice - and slowly crank the bench vice jaws down until the pressure pushes the pin straight through the trigger guard, and into the opposite ear. One point to note - if you use the TANGODOWN BG-16 pistol grip you will need to remove some of the forward lip material on the grip itself, which covers the trigger guard "gap." Easy enough to do, and will look perfectly fine when modified.
Sehr empfehlenswert
awesome! 20.08.2009
Installation was quick and painless, and it looks very nice!
It appears a lot tougher than the original guard, and it is also much more comfortable being wider and much smoother -- no sharp edges or casting seams to be found anywhere. It's a very well-finished, quality part.
In the right light, I can see the finish isn't -exactly- the same as my M&P-15 (a little more purple) but it is still very close, if you're into the whole making sure all of your AR parts match in color.
Overall, I would have to say this is the best trigger guard on the market and a must for any quality AR-15.
Sehr empfehlenswert
Great trigger guard 06.08.2009
The trigger guard is great, It is a huge step above the one that comes standard in lower parts kits. All aluminum and much more confortable to hold.
However the prices have been on these for dealers. Which is a bummer.
Sehr empfehlenswert
Works as advertised, looks great! 04.08.2009
Not much to say about the Enhanced Trigger Guard. It's aesthetically pleasing, makes the weapon more comfortable by filling in the gap between a standard grip and the "ears" of the lower receiver, installation is a breeze. This is a must have for every AR15 I own.
Sehr empfehlenswert
Great fit, good looking 23.06.2009
I have this trigger guard on all my rifles. It has a great look, and fits very well. It covers the little gap so your middle finger doesn't get indenture marks from holding the grip high. Enough room to wear gloves and use the trigger without feeling cramp. My BAD works good with it too.
Upgrade deinen AR-15/M16 mit dem MAGPUL Abzugsbügel! 🔧 Er bietet einfachen Zugang, auch mit Handschuhen. Perfekt für kalte Tage!
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Der MAGPUL B.A.D. Lever verbessert die Effizienz deines AR-15, indem er eine einfache Bedienung des Verschlussfanghebels ermöglicht.
Er ist aus hochwertigem 6061-T6 Aluminium gefertigt und bietet eine robuste und zuverlässige Leistung.
Die Montage erfolgt ohne permanente Modifikation der Waffe und ist kompatibel mit den meisten Standard-AR-15/M16 Empfängern.
Der Magpul MOE Griff verbessert den Komfort und die Kontrolle beim Schießen.
Er besteht aus robustem, hochschlagfestem Polymer und bietet eine texturierte Oberfläche für besseren Halt.
Das ergonomische Design und die Kompatibilität mit MIAD Grip Cores ermöglichen eine individuelle Anpassung deines Waffenzubehörs.
Der MAGPUL AR-15 CTR Schubschaft sorgt für ein stabiles Gefühl beim Anlegen des Gewehrs dank des Reibungsverriegelungsmechanismus.
Er ist aus robustem Nylon-Polymer gefertigt und bietet maximale Schlagfestigkeit sowie Hitzebeständigkeit.
Der Schubschaft ist in verschiedenen Farben erhältlich und passt auf mil-spec 1,14" O.D. Carbine-Pufferrohre.
Der MAGPUL MOE Abzugsbügel bietet eine flache „V“-Form für mehr Platz, besonders mit Handschuhen.
Er ist aus leichtem, verstärktem Polymer gefertigt, das fast so stark wie Aluminium ist und widerstandsfähig gegen verschiedene Wetterbedingungen.
Die Installation ist einfach und erfordert keine dauerhaften Änderungen am Empfänger; das Original kann jederzeit wieder angebracht werden.
Das PMAG ist ein 30-Schuss Magazin, das mit AR-15 kompatibel ist.
Es bietet eine verbesserte Polymer-Konstruktion und ist stoßfest.
Das Magazin ist für 5.56mm/.223 Munition geeignet und hat eine abnehmbare Staubabdeckung.
Die MAGPUL MOE Abzugsbügel bietet eine verbesserte „V“-Form für mehr Platz beim Schießen mit Handschuhen.
Hergestellt aus leichtem, verstärktem Polymer, das hitze-, kälte- und feuchtigkeitsbeständig ist.
Passt auf die meisten AR-15/M16 und AR-Stil .308 Gewehre und lässt sich einfach installieren.