Füge die gesamte Bequemlichkeit eines abnehmbaren Kastenmagazins zu deinem Lieblings-Remington 700 BDL hinzu. Der federbelastete Fingerhebel im Abzugsbügel lässt das Kastenmagazin schnell frei, was das Laden und Entladen beschleunigt. Hergestellt aus strapazierfähigem Edelstahl und mit einer back-on, matten, schwarzen Teflon®-Beschichtung versehen, die selbstschmierend ist und Kratzer sowie Abnutzung widersteht. Die aktualisierte Version hat positive Verriegelungsfedern an der Unterseite beider Seiten der Bodenplatte (hält das Magazin sicher an Ort und Stelle ohne den Gummiring), einen Polymerfuß an der Unterseite des Kastens (einfacher zu entfernen) und einen Führungsnut sowie einen größeren hinteren Fangmechanismus auf der Rückseite des Kastens (sorgt für einen ordnungsgemäßen Verschluss). Kann mit mehreren Langaction-Kalibern verwendet werden.
Add all the convenience of drop-free, box magazine to your favorite Remington 700 BDL. Spring-loaded finger latch inside the triggerguard drops the box magazine free, speeds loading and unloading. Made from durable stainless steel and finished with bake-on, matte, black Teflon® coating that's self-lubricating and resists scratches and wear. Updated version have positive locking springs on the bottom of both sides of the floor plate (holds the magazine box securely in place without the rubber o-ring), a polymer boot on bottom of box (easier to remove), and a guide slot and larger rear catch on back of box (ensures proper latch). Can be used with multiple long action caliber.
Füge die gesamte Bequemlichkeit eines abnehmbaren Kastenmagazins zu deinem Lieblings-Remington 700 BDL hinzu. Der federbelastete Fingerhebel im Abzugsbügel lässt das Kastenmagazin schnell frei, was das Laden und Entladen beschleunigt. Hergestellt aus strapazierfähigem Edelstahl und mit einer back-on, matten, schwarzen Teflon®-Beschichtung versehen, die selbstschmierend ist und Kratzer sowie Abnutzung widersteht. Die aktualisierte Version hat positive Verriegelungsfedern an der Unterseite beider Seiten der Bodenplatte (hält das Magazin sicher an Ort und Stelle ohne den Gummiring), einen Polymerfuß an der Unterseite des Kastens (einfacher zu entfernen) und einen Führungsnut sowie einen größeren hinteren Fangmechanismus auf der Rückseite des Kastens (sorgt für einen ordnungsgemäßen Verschluss). Kann mit mehreren Langaction-Kalibern verwendet werden.
Top Takeaways
Füge deiner Remington 700 BDL ein herausnehmbares Kastenmagazin hinzu, das das Laden und Entladen erleichtert.
Das langlebige Design aus Edelstahl mit mattem, schwarzem Teflon®-Finish widersteht Kratzern und Verschleiß.
Die aktualisierte Version bietet positive Verriegelungsfedern und einen Polymer-Stiefel für einfacheren Zugriff und bessere Funktionalität.
Eigenschaften
Finish:Black
Modell:700
Waffentyp:Remington
Versandgewicht:0,272kg
Versandhöhe:25mm
Versandbreite:76mm
Versandlänge:152mm
Artikeldetails
Made in USA
US-Exportklassifizierung: 0A501.x
Kundenbewertungen
Kundenbewertungen (4)
4 / 5
Nicht empfehlenswert
Mag may drop out with recoil 21.05.2017
I had an HS Precision rifle in .375 RUM (with HS Precision bottom metal, perhaps prior to the design improvements mentioned in the description) which I took to Africa (push-feed action, detachable mag not a good choice for dangerous game, but I was inexperienced). The rifle frequently dropped the mag on the ground with a shot, and I first thought it a problem with the latch. I sent it back to HS P and they assured me the problem was solved. It was not, and I sold the gun to a friend, with full disclosure of my concern. We were later on a safari together when (it continued to drop the mag) we figured out the problem. With a heavy recoil caliber, as the gun recoils, the shooter's finger may contact the latch release, as it is in line with the trigger, rather than below it, as in a Dakota action. Some tape wrapped around the latch release to make it require more pressure to release the mag solved the problem temporarily. A friend recently bought a custom rifle in a .300 mag and it arrived with an HS Precision bottom metal. Shot it off sticks and --- SAME PROBLEM! We are on the Brownell's site to buy a replacement bottom.
You may not have this problem with a light recoil caliber, or if shooting with the mag supported, i.e. bench or over a pack. Beware if you are shooting off-hand or off sticks. If the latch release were moved to the bottom of the trigger guard so as not to be in line with the finger upon recoil, it would solve this issue. Bottom line, I have had experience with this bottom metal twice; both drop the mag on the shot off sticks. I would only consider this bottom for light recoil calibers.
Sehr empfehlenswert
Great DBM system 18.08.2016
I got one of these for my R-700 Sendero 7mm magnum. Very easy installation. All you do is file a small part of the stock out and it fits well. I have these HS DBM systems for my other rifles too, and they're a big upgrade over the internal box system Remington has. If you have some extra money buy one.
Sehr empfehlenswert
Huge improvement over stock magazine 23.03.2015
This was exactly what I needed for my Remington 700 Long Range chambered in 7mm Rem Mag. The internal magazine system that Remington produced for my rifle was absolute garbage. The feed lips marked up the brass terrible with deep gouges and the feed ramp is rough which scraped up the bullet during feeding. To top it all off it was a serious challenge even getting the rounds to stay in there without flying out randomly. This fine piece of equipment fixed all of that. Feeding rounds through the magazine leaves no marks or scrapes on the brass, and the bullet now bypasses the rough section of my feed ramp so no scratches on the bullet either. Some extremely minor fitting was required to my Bell and Carlson M40 stock, but it only took about 5 minutes with a file, hammer, and flat tip screwdriver to knock out a small portion for a perfect, snug fit. Overall I am very happy and would recommend this to anyone looking for a detachable mag system. Stock bottom metal screws worked just fine too!
Sehr empfehlenswert
Great product and will purchase more 01.01.2013
Everything is quality about this product.
Extremely happy with the look and how it functions. I have installed two of these on Bell and Carlson stocks. Basically a drop in with one minor adjustment. You have to take out a 1/8 by 1/8 spot of the stock where the hinge pivots when releasing the magazine. Easily done with a dremel (I used the router bit- 5 min). Front screw flange sets a little proud but not at all a show stopper. A couple of thousandths is all. Not at all clumsy with all the hanging of the other makers bottom metal.
Brownells Deutschland GmbH
Lahnstr. 1
24539 Neumünster
Deutschland
info@brownells-deutschland.de
Zuletzt gesehen
Ups! Da ist etwas schiefgelaufen.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.
Erlebe die Bequemlichkeit des H-S PRECISION Remington 700 Long Action Detachable Magazine! 🛠️ Robust, einfach zu bedienen und perfekt für dein Gewehr.
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Das abnehmbare Kastenmagazin ist speziell für die H-S Precision 300 Winchester Magnum Umrüstung konzipiert.
Das Edelstahlmagazin mit Teflonbeschichtung bietet eine snag-freie Handhabung und hat eine glatte Bodenplatte.
Das 3-Schuss Modell ist in einem flachen Profil erhältlich und passt nicht auf vorherige Generationen von HS Bodenmetallen.
Füge deiner Remington 700 BDL ein freifallendes, kastenförmiges Magazin hinzu, das das Laden und Entladen beschleunigt.
Das Magazin besteht aus strapazierfähigem Edelstahl mit einer matten, schwarzen Teflon®-Beschichtung, die Kratzern und Abnutzung widersteht.
Die aktualisierte Version hat positive Verriegelungsfedern, einen leichter zu entfernenden Polymerfuß und eine größere hintere Falle für ein sicheres Einrasten.