Fully-Lined Barrel Grooves Prevent Slipping And Damage
Massive aluminum jaws lined with space age polyurethane elastomer grip tight and prevent marring on AR-15/M16 barrels. Two grooves fit standard and heavy barrel contours.
SPECS: Machined aluminum with permanently bonded green polyurethane elastomer lining. 5" (12.7cm) wide, 1" (2.5cm) thick, 3-7/8" (9.8cm) long. 2 lb. 6 oz. (1kg) wt. Fits 4" and wider vises.
Mehr...
Vollständig ausgekleidete Lauf-Rillen verhindern Verrutschen und Beschädigungen
Massive Aluminiumbacken, ausgekleidet mit modernem Polyurethan-Elastomer, bieten festen Halt und verhindern Kratzer an AR-15/M16 Läufen. Zwei Rillen passen zu Standard- und schweren Laufkonturen.
SPECS: Bearbeiteter Aluminium mit dauerhaft verbundenem grünen Polyurethan-Elastomer-Beschichtung. 5" (12,7 cm) breit, 1" (2,5 cm) dick, 3-7/8" (9,8 cm) lang. 2 lb. 6 oz. (1 kg) Gewicht. Passt auf Schraubstöcke mit 4" und breiteren Öffnungen.
Mehr...
Kundenbewertungen zu SATURN PRODUCTS Accu-Grip Vise Jaws
Anzahl der Bewertungen: 9
Von brownells.com: 9
Durchschnittliche Bewertung: 4,2
If you're removing a barrel, buy it!(18.12.2009)
First off, I'm not quite sure why this is advertised for AR-15's only-- a barrel is a barrel, and this should work fine for about any gun. I've removed barrels using this product, as well as plain-jane wood blocks that are channeled out. The gripping surface on this tool is far superior to plain wood-- and grip is what it's all about when referencing blocks and vises. It's worth the extra cost.
Does not work with FN SCAR barrels(09.03.2010)
Description states that it works with 5.56 pencil barrels, but this is not accurate. Using the "pencil barrel" smaller diameter blocks, the aluminum blocks clamped shut in vise before rubber was touching the sides of the barrel. Barrel not only spun, but the was enough gap there to wobble the barrel.
Worked as advertised(18.05.2010)
Held the barrel, did not slip, did not mare the finish, very good tool. I bought this because I got a compensator for my M4, I removed the A2 flash hider with a strap wrench, but could not fully install the new compensator. Ordered this on a friday and got it on monday, pulled it out of the box, put the blocks in my vise, separated my upper and lower reciever, removed all the tactical toys off of the upper, set the barreled upper in the vise blocks, tightened the vise, put a wrench on my compensater and tightened it the rest of the way. Done! All in less time than it took me to type this and I was hobbleing around on crutches(softball injurie).
Good vise jaws(23.05.2010)
I use these to change M16 and M4 barrels, and they do a great job of not marring the barrel. The one change needed on this tool is a notch cut out for the bayonet lug, which prevents the barrel from spinning without having to tighten the vise with all of your might.
Barrel vice block(14.11.2011)
Works
So Easy A Caveman Can Use It(16.03.2012)
first off I am a Police armorer who works on various weapons platforms that my agency carries. I also have a gun business on the side that I do custom work. I purchased a set of the Accu-Grip vise jaws after having difficulty with the set that I had. WOW! what a difference these things were like a gift from heaven. They work well with H-Bars and Standard Barrel configs. I would highly recommend these to the professional or the novice building a black rifle. Well worth the money spent, you'll have less agravation in the long run.
Good barrel vise jaws(12.05.2012)
Quality contruction and they work.
Just works(24.01.2013)
I've had a set of these since the builder gave me a set in gunsmithing school. Haven't found much through the years that they won't hold.
works well.(28.03.2016)
It did not fit the barrels I was working on as received (too loose). I cut a strip of leather that would fit in one side and that tightened it right up, I then had no problem tightening up the compensator against the crush washer. This thing works well... but it wont fit every barrel profile right out of the box.
Artikel-Nr.: 852015000 SATURN PRODUCTS Accu-Grip Vise Jaws Herstellerproduktnummer: NONE Massive Aluminiumbacken, ausgekleidet mit modernem Polyurethan-Elastomer, bieten festen Halt und verhindern Kratzer an AR-15/M16 Läufen. Zwei Rillen passen zu Standard- und schweren Laufkonturen.
224.9EUR52224,90 €
*
Lieferzeit ca. 14-21 Tage. Mehr als 10 Stk. im Großlager
Fully-Lined Barrel Grooves Prevent Slipping And Damage
Massive aluminum jaws lined with space age polyurethane elastomer grip tight and prevent marring on AR-15/M16 barrels. Two grooves fit standard and heavy barrel contours.
SPECS: Machined aluminum with permanently bonded green polyurethane elastomer lining. 5" (12.7cm) wide, 1" (2.5cm) thick, 3-7/8" (9.8cm) long. 2 lb. 6 oz. (1kg) wt. Fits 4" and wider vises.
Mehr...
Vollständig ausgekleidete Lauf-Rillen verhindern Verrutschen und Beschädigungen
Massive Aluminiumbacken, ausgekleidet mit modernem Polyurethan-Elastomer, bieten festen Halt und verhindern Kratzer an AR-15/M16 Läufen. Zwei Rillen passen zu Standard- und schweren Laufkonturen.
SPECS: Bearbeiteter Aluminium mit dauerhaft verbundenem grünen Polyurethan-Elastomer-Beschichtung. 5" (12,7 cm) breit, 1" (2,5 cm) dick, 3-7/8" (9,8 cm) lang. 2 lb. 6 oz. (1 kg) Gewicht. Passt auf Schraubstöcke mit 4" und breiteren Öffnungen.
Mehr...
Kundenbewertungen zu SATURN PRODUCTS Accu-Grip Vise Jaws
Anzahl der Bewertungen: 9
Von brownells.com: 9
Durchschnittliche Bewertung: 4,2
If you're removing a barrel, buy it!(18.12.2009)
First off, I'm not quite sure why this is advertised for AR-15's only-- a barrel is a barrel, and this should work fine for about any gun. I've removed barrels using this product, as well as plain-jane wood blocks that are channeled out. The gripping surface on this tool is far superior to plain wood-- and grip is what it's all about when referencing blocks and vises. It's worth the extra cost.
Does not work with FN SCAR barrels(09.03.2010)
Description states that it works with 5.56 pencil barrels, but this is not accurate. Using the "pencil barrel" smaller diameter blocks, the aluminum blocks clamped shut in vise before rubber was touching the sides of the barrel. Barrel not only spun, but the was enough gap there to wobble the barrel.
Worked as advertised(18.05.2010)
Held the barrel, did not slip, did not mare the finish, very good tool. I bought this because I got a compensator for my M4, I removed the A2 flash hider with a strap wrench, but could not fully install the new compensator. Ordered this on a friday and got it on monday, pulled it out of the box, put the blocks in my vise, separated my upper and lower reciever, removed all the tactical toys off of the upper, set the barreled upper in the vise blocks, tightened the vise, put a wrench on my compensater and tightened it the rest of the way. Done! All in less time than it took me to type this and I was hobbleing around on crutches(softball injurie).
Good vise jaws(23.05.2010)
I use these to change M16 and M4 barrels, and they do a great job of not marring the barrel. The one change needed on this tool is a notch cut out for the bayonet lug, which prevents the barrel from spinning without having to tighten the vise with all of your might.
Barrel vice block(14.11.2011)
Works
So Easy A Caveman Can Use It(16.03.2012)
first off I am a Police armorer who works on various weapons platforms that my agency carries. I also have a gun business on the side that I do custom work. I purchased a set of the Accu-Grip vise jaws after having difficulty with the set that I had. WOW! what a difference these things were like a gift from heaven. They work well with H-Bars and Standard Barrel configs. I would highly recommend these to the professional or the novice building a black rifle. Well worth the money spent, you'll have less agravation in the long run.
Good barrel vise jaws(12.05.2012)
Quality contruction and they work.
Just works(24.01.2013)
I've had a set of these since the builder gave me a set in gunsmithing school. Haven't found much through the years that they won't hold.
works well.(28.03.2016)
It did not fit the barrels I was working on as received (too loose). I cut a strip of leather that would fit in one side and that tightened it right up, I then had no problem tightening up the compensator against the crush washer. This thing works well... but it wont fit every barrel profile right out of the box.