The same, 100% bigger, mag well opening for “can’t miss” mag changes with narrower sides that match thinner, slim grips. Checkered 20 lpi, unless otherwise noted as Smooth.
Mehr...
Extra-Breit für Schnellere Nachladevorgänge
Der gleiche, 100 % größere Magwell-Ausschnitt für "kann nicht verfehlen" Magazinwechsel mit schmaleren Seiten, die zu dünneren, schlanken Griffen passen. Gecheckt mit 20 lpi, es sei denn, es ist anders als glatt angegeben.
Mehr...
Kundenbewertungen zu SMITH & ALEXANDER Flat Blue 1911 Govt-Commander
Anzahl der Bewertungen: 23
Von brownells.com: 23
Durchschnittliche Bewertung: 4,3
It dropped in my Wilson CQB(06.04.2012)
I like thin grips and wanted a mag guide to compliment them. I also like the arched main strap,,, this fulfilled both requirements. It was a perfect fit. Nothing was done. It just FIT perfectly. It tends to give the pistol a "rounded butt" feel and eliminates the sharp edge of the Wilson speed chute.
Rock Solid Product(28.10.2009)
This is a great product. I had it installed in no time. It fits very tight, plus its steel which added some weight to my frame. Works very well with my G10 Grips, no gapping at the base. Overall it was a sound investment.
S&A Mag Guide on Colt Agent(28.06.2012)
I ordered a Mag Guide for a spanking new Talo Colt Agent... I was hoping fitting would be minimal, My fingers were crossed that the finish was at least close...
This thing was SPOT ON. NO gapping, NO overlap, NO need to touch it with file nor stone. 3 minute install.
I don't know about other brands of 1911s, but these mag guides fit Colts as if the Factory themselves made it.
Thanks S&A and to the Brownell Team for fast service and competitive pricing.
Good product easy install...(01.02.2010)
Bought this couple of days ago and was able to install it myself in a about 10 minutes. Finish seems tad thin so I haven't got much expectations for wear (this is on my daily CCW) but no issues with fit on my Kimber Ultra Carry. This is replacing the wilson combat ez-loader and is MUCH BETTER. One piece, no rattles!
Fits well(15.05.2014)
Dropped into a Ruger SR 1911 lined up as it should. Mainspring bore a little rough but didn't bind, just not as nice as I have received from other brands. I always expect some fitting or polishing, OCD I guess. Overall very nice product.
Fits great, looks awesome(03.11.2014)
This magwell works great, drop in is fast on a SA Loaded. No fitting required. Great finish too. If using the stock grips like I did, I thought it was best to buy the slim line, but the standard would probably look best with the width of the grip. I like it overall. Easy 1 minute install.
Best $ I've spent!(15.02.2016)
Works great, easy to install, doesn't print under clothing as bad as the "flat"! What more do you need to know? Best money I've spent on my 1911 yet!
Drop in for Sig Traditional Match Elite (29.03.2016)
This slid right into my Sig Traditional Match Elite 9 mm 1911. No fitting required and a very quick and simple install.
The mag well will help speed my reload time but what I really got it for was to adjust my grip a little on this gun. I have big hands and this seems to help.
S&A GM Mag guide(09.04.2011)
about 10 min install with only a drift. A little sharp at the rear bottom checkering (touched up w/file in 20 sec.) EASY reloads w/mags w/bumpers. seating mags w/o pads requires attention.
PERFECT!(17.08.2011)
This slipped right into my Springfield Mil Spec. I have VZ slim grips on and the profile matched perfectly. I also find the flat profile much more comfortable than the original arched MSH.
eazy install(11.10.2011)
10 min install very eazy watched youtube no problem
nope(01.06.2012)
It fit but very very bad finish. Raised above the frame creating too many surfaces to be comfortable. Magwell not flushed to frame.
Kimber SS II
Needs fitment(26.09.2012)
Unfortunately, not an easy install on my Springfield Armory Loaded .45. I've installed dozens of MSHs, but this one was different. Even though it fits the frame fine, the hole for the MSH retention spring is a bit off spec. I knew this as soon as I was tapping the pin in, there was quite a bit of resistance and small burs of metal coming through. The hole will require some careful enlargement from my gunsmith. Overall seems like a heavy duty stainless steel product, but not what I expected, however. Would recommend only with reservations.
Good fit on Colt Rail Gun(19.04.2014)
Quick install on Colt Stainless Rail Gun. Finish closely matches that of gun. No fitting required and left only the slightest gap between mag-guide and bottom of frame. You will need mag-bumpers for reliable mag seating. Not only increases mag-well size but lengthens grip slightly for increased leverage.
Not as easy as the blued magwell!(01.05.2016)
Not as easy to install on my older model Loaded Springfield as was the blued version on my parkerized Loaded. Doesn't seem to fit as well as the blued one and I will have to have a gunsmith blend it to the frame. Most folks will find fitting needed but part does work.
Impressive !(18.04.2012)
Easy 5 minute install, even for someone that hasn't done it before.
Fit my Taurus PT1911 perfectly !
Not pleased (08.07.2015)
Very disappointed. Usually I find Harrison design products to be top notch and that is why I ordered this piece. Looks nice, feels nice but very loose on a Colt M1991 A1. mainspring housing pin fell right through it. Even an oversize pin was loose. Would have required a lot of filing and fitting to get it even close to flush in some areas.
First time I have ever sent a product back to Brownells.
Great Addition to any 1911 Pistol(19.05.2010)
I have a Springfield Armory 1911-A1 Loaded that is one of my primary Carry Sidearms and I wanted a slimmer magwell since I switched to Pachmayr GM45C grips and this Magwell is PERFECT!
Makes a 1911 look awesome(15.08.2011)
I have a Fullsize Kimber Custom #1 that is one of my primary carry weapons and competitively shoot with. I want a slimmer magwell for assisting in engaging my magazines in the weapon and giving it a slim tight fit look. S & A slimline magwells are a perfect fit to any 1911.
Perfect Fit(03.03.2012)
I installed this on my Kimber Warrior without any trouble. It was a perfect fit and looks great. I would highly recommend it to anyone with a 1911 without a magwell.
Looks and works great(22.08.2015)
Great functional and good looking addition to my 1911 build.
Funnels mags into the magwell easily without a lot of extra bulk. Simple easy install, and works wonderfully. Great grip in the checkering to keep hold of the gun.
Really like it!(01.05.2016)
Easy to install, fit my Loaded Springfield to a "T". Absolutely no fitting needed...even doing it myself it looks like someone from Wilson Combat installed it!
Perfect Fit, Easy Installation(16.02.2018)
Installation was less than 10 minutes. The fit on my S&W ProSeries was perfect. The fit also matched my VZ slimline grips perfect. The finish matched the gun about as close as you will get for an aftermarket part.
Artikel-Nr.: 849000007 SMITH & ALEXANDER Flat Blue 1911 Govt-Commander Der gleiche, 100 % größere Magwell-Ausschnitt für "kann nicht verfehlen" Magazinwechsel mit schmaleren Seiten, die zu dünneren, schlanken Griffen passen. Gecheckt mit 20 lpi, es sei denn, es ist anders als glatt angegeben.
Made in USA
US-Exportklassifizierung: 0A501.y.1
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Brownells Deutschland GmbH
Lahnstr. 1
24539 Neumünster
Deutschland
info@brownells-deutschland.de
Artikel-Nr.: 849000009 SMITH & ALEXANDER Flat Stainless Steel 1911 Govt-Commander Der gleiche, 100 % größere Magwell-Ausschnitt für "kann nicht verfehlen" Magazinwechsel mit schmaleren Seiten, die zu dünneren, schlanken Griffen passen. Gecheckt mit 20 lpi, es sei denn, es ist anders als glatt angegeben.
Made in USA
US-Exportklassifizierung: 0A501.y.1
Dieses Produkt unterliegt der Aufsicht der Regierung der Vereinigten Staaten von Amerika und ist ausschließlich für den Export in das Bestimmungsland zur Verwendung durch den endgültigen Empfänger oder Endverbraucher, der beim Kauf festgelegt wird, bestimmt. Dieses Produkt darf ohne vorherige Erlaubnis der Regierung der Vereinigten Staaten von Amerika oder einer autorisierten US-Behörde über den endgültigen Empfänger oder Endverbrauchers hinaus nicht wiederverkauft, übertragen, oder in einer anderen Weise in Drittländer oder an Dritte überlassen werden. Dies gilt auch dann, wenn die Artikel verbaut bzw. in einen anderen Artikel integriert wurde.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
The same, 100% bigger, mag well opening for “can’t miss” mag changes with narrower sides that match thinner, slim grips. Checkered 20 lpi, unless otherwise noted as Smooth.
Mehr...
Extra-Breit für Schnellere Nachladevorgänge
Der gleiche, 100 % größere Magwell-Ausschnitt für "kann nicht verfehlen" Magazinwechsel mit schmaleren Seiten, die zu dünneren, schlanken Griffen passen. Gecheckt mit 20 lpi, es sei denn, es ist anders als glatt angegeben.
Mehr...
Kundenbewertungen zu SMITH & ALEXANDER Flat Blue 1911 Govt-Commander
Anzahl der Bewertungen: 23
Von brownells.com: 23
Durchschnittliche Bewertung: 4,3
It dropped in my Wilson CQB(06.04.2012)
I like thin grips and wanted a mag guide to compliment them. I also like the arched main strap,,, this fulfilled both requirements. It was a perfect fit. Nothing was done. It just FIT perfectly. It tends to give the pistol a "rounded butt" feel and eliminates the sharp edge of the Wilson speed chute.
Rock Solid Product(28.10.2009)
This is a great product. I had it installed in no time. It fits very tight, plus its steel which added some weight to my frame. Works very well with my G10 Grips, no gapping at the base. Overall it was a sound investment.
S&A Mag Guide on Colt Agent(28.06.2012)
I ordered a Mag Guide for a spanking new Talo Colt Agent... I was hoping fitting would be minimal, My fingers were crossed that the finish was at least close...
This thing was SPOT ON. NO gapping, NO overlap, NO need to touch it with file nor stone. 3 minute install.
I don't know about other brands of 1911s, but these mag guides fit Colts as if the Factory themselves made it.
Thanks S&A and to the Brownell Team for fast service and competitive pricing.
Good product easy install...(01.02.2010)
Bought this couple of days ago and was able to install it myself in a about 10 minutes. Finish seems tad thin so I haven't got much expectations for wear (this is on my daily CCW) but no issues with fit on my Kimber Ultra Carry. This is replacing the wilson combat ez-loader and is MUCH BETTER. One piece, no rattles!
Fits well(15.05.2014)
Dropped into a Ruger SR 1911 lined up as it should. Mainspring bore a little rough but didn't bind, just not as nice as I have received from other brands. I always expect some fitting or polishing, OCD I guess. Overall very nice product.
Fits great, looks awesome(03.11.2014)
This magwell works great, drop in is fast on a SA Loaded. No fitting required. Great finish too. If using the stock grips like I did, I thought it was best to buy the slim line, but the standard would probably look best with the width of the grip. I like it overall. Easy 1 minute install.
Best $ I've spent!(15.02.2016)
Works great, easy to install, doesn't print under clothing as bad as the "flat"! What more do you need to know? Best money I've spent on my 1911 yet!
Drop in for Sig Traditional Match Elite (29.03.2016)
This slid right into my Sig Traditional Match Elite 9 mm 1911. No fitting required and a very quick and simple install.
The mag well will help speed my reload time but what I really got it for was to adjust my grip a little on this gun. I have big hands and this seems to help.
S&A GM Mag guide(09.04.2011)
about 10 min install with only a drift. A little sharp at the rear bottom checkering (touched up w/file in 20 sec.) EASY reloads w/mags w/bumpers. seating mags w/o pads requires attention.
PERFECT!(17.08.2011)
This slipped right into my Springfield Mil Spec. I have VZ slim grips on and the profile matched perfectly. I also find the flat profile much more comfortable than the original arched MSH.
eazy install(11.10.2011)
10 min install very eazy watched youtube no problem
nope(01.06.2012)
It fit but very very bad finish. Raised above the frame creating too many surfaces to be comfortable. Magwell not flushed to frame.
Kimber SS II
Needs fitment(26.09.2012)
Unfortunately, not an easy install on my Springfield Armory Loaded .45. I've installed dozens of MSHs, but this one was different. Even though it fits the frame fine, the hole for the MSH retention spring is a bit off spec. I knew this as soon as I was tapping the pin in, there was quite a bit of resistance and small burs of metal coming through. The hole will require some careful enlargement from my gunsmith. Overall seems like a heavy duty stainless steel product, but not what I expected, however. Would recommend only with reservations.
Good fit on Colt Rail Gun(19.04.2014)
Quick install on Colt Stainless Rail Gun. Finish closely matches that of gun. No fitting required and left only the slightest gap between mag-guide and bottom of frame. You will need mag-bumpers for reliable mag seating. Not only increases mag-well size but lengthens grip slightly for increased leverage.
Not as easy as the blued magwell!(01.05.2016)
Not as easy to install on my older model Loaded Springfield as was the blued version on my parkerized Loaded. Doesn't seem to fit as well as the blued one and I will have to have a gunsmith blend it to the frame. Most folks will find fitting needed but part does work.
Impressive !(18.04.2012)
Easy 5 minute install, even for someone that hasn't done it before.
Fit my Taurus PT1911 perfectly !
Not pleased (08.07.2015)
Very disappointed. Usually I find Harrison design products to be top notch and that is why I ordered this piece. Looks nice, feels nice but very loose on a Colt M1991 A1. mainspring housing pin fell right through it. Even an oversize pin was loose. Would have required a lot of filing and fitting to get it even close to flush in some areas.
First time I have ever sent a product back to Brownells.
Great Addition to any 1911 Pistol(19.05.2010)
I have a Springfield Armory 1911-A1 Loaded that is one of my primary Carry Sidearms and I wanted a slimmer magwell since I switched to Pachmayr GM45C grips and this Magwell is PERFECT!
Makes a 1911 look awesome(15.08.2011)
I have a Fullsize Kimber Custom #1 that is one of my primary carry weapons and competitively shoot with. I want a slimmer magwell for assisting in engaging my magazines in the weapon and giving it a slim tight fit look. S & A slimline magwells are a perfect fit to any 1911.
Perfect Fit(03.03.2012)
I installed this on my Kimber Warrior without any trouble. It was a perfect fit and looks great. I would highly recommend it to anyone with a 1911 without a magwell.
Looks and works great(22.08.2015)
Great functional and good looking addition to my 1911 build.
Funnels mags into the magwell easily without a lot of extra bulk. Simple easy install, and works wonderfully. Great grip in the checkering to keep hold of the gun.
Really like it!(01.05.2016)
Easy to install, fit my Loaded Springfield to a "T". Absolutely no fitting needed...even doing it myself it looks like someone from Wilson Combat installed it!
Perfect Fit, Easy Installation(16.02.2018)
Installation was less than 10 minutes. The fit on my S&W ProSeries was perfect. The fit also matched my VZ slimline grips perfect. The finish matched the gun about as close as you will get for an aftermarket part.
Hilfe und Kontakt
(0) 
Newsletter
Klassische Ansicht
Mobile Ansicht