Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Großlager.
Bestellbar, nicht vorrätig
Patrone: 223 WSSM (Winchester Super Short Mag), 243 WSSM (Winchester Super Short Mag), 270 WSM (Winchester Short Mag), 7 mm Remington Magnum, 257 Weatherby Magnum, 264 Winchester, 6.5 mm Remington Magnum, 270 Weatherby MagnumArtikel-Nr.: 100010065
734307905217 Universeller Hülsenhalter, der in den meisten Marken von Wiederladepressen verwendet wird. Funktioniert nicht mit Lee Auto Prime. Sieh dir das Lee Hülsenhalter-Diagramm an.
Bestellbar, nicht vorrätig
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Großlager.
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Großlager.
Nachbestellt, Lieferzeit ca. 4-12 Wochen aus dem Großlager.
Bestellbar, nicht vorrätig
Patrone: 223 WSSM (Winchester Super Short Mag), 243 WSSM (Winchester Super Short Mag), 270 WSM (Winchester Short Mag), 7 mm Remington Magnum, 257 Weatherby Magnum, 264 Winchester, 6.5 mm Remington Magnum, 270 Weatherby MagnumArtikel-Nr.: 100010065
Universal shell holder used in most brands of reloading presses. Will not work with Lee Auto Prime. View Lee Shellholder Chart
Universeller Hülsenhalter, der in den meisten Marken von Wiederladepressen verwendet wird. Funktioniert nicht mit Lee Auto Prime. Sieh dir das Lee Hülsenhalter-Diagramm an.
Eigenschaften
Art:Press Type
Patrone:17 Remington,204 Ruger,221 Remington Fireball,222 Remington,222 Remington Mag,223 Remington,5.56 mm NATO,6 x 47 (6 mm/222 Mag),7 mm TCU
Versandgewicht:0,159kg
Versandhöhe:13mm
Versandbreite:97mm
Versandlänge:130mm
UPC:734307905217
Artikeldetails
Made in USA
Kundenbewertungen
Kundenbewertungen (1)
4 / 5
Empfehlenswert
Modified for Sinclair priming tool 13.12.2017
The Sinclair priming tool is in my opinion the best for accurately and consistently seating primers. However, for .338 LM (based on .416 Rigby) there are not a lot of options. The proper Sinclair holder is backordered from Brownell.
However the Sinclair tool accepts Lee hand priming tool shell holders and the #8 Lee shell holder fits and can be installed into the Sinclair tool by facing off the lug that holds the shell holder into a press thus converting it to a Lee priming-type shell holder, in other words just make this holder flat across the bottom as are the Lee priming shell holders. I did this easily in the lathe, a 5 minute job.
You may also need to modify the primer cup in the Sinclair tool to allow a case to fit smoothly. I took .025 off the lip of the cup to match the shell holder floor. The Sinclair plunger is adjustable (see their directions) and it sets primers just below flush when is set to .010 above the lip of the primer cup.
Brownells Deutschland GmbH
Lahnstr. 1
24539 Neumünster
Deutschland
info@brownells-deutschland.de
Zuletzt gesehen
Ups! Da ist etwas schiefgelaufen.
Beim Laden dieses Inhalts ist ein Fehler aufgetreten. Bitte aktualisiere die Seite, um fortzufahren. Wenn das Problem weiterhin besteht, wende dich bitte an unseren Kundenservice.